A black Korgi Ball with two glowing eyes A purple Korgi Ball with two glowing eyes

Pre-order · Founders Edition · 25 numbered kits

Build-a-Korgi.

The Korgi Ball kit: everything for your own Korgi Ball except the board and the battery. Add a Waveshare board, follow the photo guide, and say “Hey Grok”.

$49

Free shipping in the US. Tax added where it applies.

Pre-order the kit

Ships in January 2027, or sooner. Full refund any time before it ships.

In the box.

  • The 3D-printed ball: body, front ring and back cap, cleaned up and ready
  • Its stand, in the same color
  • The USB-C port for the back, already fitted in the cap
  • The short flat cable that joins the board to that port
  • Guide and access to source code
  • Your Founders Edition card

No soldering and no 3D printer needed. It goes together in under an hour, with twist-on parts and plugs.

Pick a color.

The Founders Edition comes in two colors. You choose when you pre-order, and the whole ball and its stand come in that color.

  • Black

  • Purple

The pictures are drawings; the printed plastic will look a little different. More colors may come later.

What you add.

You buy these from their sellers; we don’t sell them.

  1. The board (needed)

    Waveshare ESP32-S3-Touch-LCD-1.85: the round touchscreen, the brain, the microphone and the speakers. Get exactly this one: other 1.85" boards look alike but won’t fit or work.

    From Waveshare · ~$34.99 From Amazon · ~$42.23

    When it arrives, look for Rev2.1 under the name on the board. See “If you add a battery” below.

  2. A battery (optional)

    Lets you carry it around the house. Without one, it runs plugged in. Any 3.7 V single-cell LiPo with a protection board and a 1.25 mm 2-pin plug, no bigger than 25 × 10 × 42 mm, like this 1100 mAh one.

    From Amazon · ~$8.99

  3. A USB-C cable to your Mac (if you need one)

    Any USB-C cable that carries data, for setup and charging. Most phone cables do.

  4. A Mac and your Grok Bot

    The Korgi Ball app on your Mac listens, asks your Grok Bot, and speaks the answer. Windows is in the works.

If you add a battery.

  • Check the board says Rev2.1. The boards we link to should be Rev2.1, but it’s worth a look: it’s printed under the name. Rev2.1 charges the battery gently. Older boards charge too fast for this small battery: run those plugged in, without a battery.
  • Check red goes to +. Battery sellers wire these plugs both ways. The guide shows how to check before you plug it in.
  • Treat it kindly. Don’t bend, pierce or squash it. If it ever gets hot or puffy, unplug it and stop using it.

For makers 14 and up.

How the pre-order works.

  1. 1

    Pre-order and pick your color. The Founders Edition is 25 kits, each numbered in the order it was pre-ordered.

  2. 2

    Order your Waveshare board, and a battery if you want one. Boards shipped from Waveshare can take a while to arrive, so order early.

  3. 3

    We print and pack your kit, and it ships in January 2027, or sooner. We email you when it’s on its way.

  4. 4

    Follow the photo guide: put the parts together, set up your board from your Mac, and say “Hey Grok”.

Questions.

Can I cancel?+

Yes. Email us any time before your kit ships and we’ll refund you in full. See the refund policy.

What if it doesn’t ship in January?+

We’ll email you with the new date, and you can wait or get a full refund.

Do I need a 3D printer or a soldering iron?+

No. We print the parts, and everything plugs or twists together.

Why isn’t the board in the kit?+

The kit is the part we make. A finished Korgi Ball with everything inside is on the way; join the waitlist to hear first.

Do you ship outside the US?+

Not for the Founders Edition. Tell us where you are and we’ll let you know.

Pre-order the kit · $49

Notes

The kit has no electronics. Prices of the board and battery were checked on November 19, 2026, and can change.